# Instrumentation and Control Technician (447A)

## Fast facts

| Trade code | 447A |
| --- | --- |
| Sector | Industrial |
| Classification | Voluntary trade |
| Certifying exam | Required (O. Reg. 876/21, s. 3) |
| Apprentice to journeyperson ratio | Not subject to a ratio |
| Red Seal trade | Yes |
| Active apprentices in Ontario | 526 (reported in Ontario's apprenticeship dataset) |
| Approved sponsors | 60 |
| Certifying body | Skilled Trades Ontario |

Last verified August 20, 2026 against the sources listed below.

## What does an instrumentation and control technician do?

An Instrumentation and Control Technician installs, maintains, calibrates, designs and troubleshoots networking systems, process control and environmental protection equipment in a variety of industrial environments.

Skilled Trades Ontario describes the work of this trade as follows:

- installs, maintains and configures control and process systems
- calibrates, commissions, configures, installs and troubleshoots all pneumatic, electronic, electrical, mechanical and analytical instrumentation devices
- calibrates and repairs analytical instrumentation that monitors or controls flow, level, temperature, pressure, acidity, conductivity and humidity
- services all process control communication networks
- sevices environmental and other analytical instruments

## How long is the instrumentation and control technician apprenticeship?

The in-school portion of this apprenticeship runs to 3 levels. Skilled Trades Ontario does not publish a total hour requirement for this trade on its trade page; confirm the current requirement in the trade's apprenticeship training standard before signing an agreement.

## What do you study in school for the 447A?

The in-school portion covers, but is not limited to:

- applied trade practices, procedures, trade standards and codes
- electrical theory and applied trade calculations
- electronic systems, computers and documentation
- instrumentation theory and process control fundamentals
- computer control systems
- analyical instrumentation, discrete control and applied circuts
- fluid power, pneumatic and mechanical devices and systems
- primary and final control elements- service, selection and theory

## Is instrumentation and control technician a compulsory trade in Ontario?

No. Instrumentation and Control Technician is a prescribed trade under section 1 of O. Reg. 876/21, but it is not on the compulsory list in section 2. That means you can legally work in this trade in Ontario without holding a Certificate of Qualification. Certification is voluntary and serves as formal proof of competency to employers and clients.

Voluntary classification only covers certification under the Building Opportunities in the Skilled Trades Act. Specific work within the trade can still require separate licences or permits under other Ontario statutes, so confirm the rules for the actual work being done. The 23 trades where certification is mandatory are on the [compulsory trades list](https://ontariocertificationregistry.ca/trades/compulsory/).

## How do you become an instrumentation and control technician in Ontario?

The apprenticeship pathway for this trade is administered by Skilled Trades Ontario under section 14 of the Building Opportunities in the Skilled Trades Act, 2021:

1. **Find a sponsor and register a training agreement.** An employer or union sponsor takes you on and the training agreement is registered with the ministry.
2. **Complete the on the job and in school training.** The skills are set out in the trade's Apprenticeship Training Standard, signed off by your sponsor as you demonstrate them, alongside levels of in school theory at a training delivery agent.
3. **Receive your Certificate of Apprenticeship.** Skilled Trades Ontario issues it when the program is complete.
4. **Pass the certifying exam.** This trade has a certifying exam under O. Reg. 876/21, s. 3. Passing it earns the Certificate of Qualification, the voluntary proof of qualification for this trade.

The exact training standard, current curriculum and program details are on the [Skilled Trades Ontario page for Instrumentation and Control Technician](https://www.skilledtradesontario.ca/trade-information/instrumentation-and-control-technician/). On the job hour requirements vary by trade and are not published on this page yet; confirm them in the training standard before signing an agreement.

## Is the 447A a Red Seal trade?

Yes. Instrumentation and Control Technician participates in the Interprovincial Red Seal Program, the national standard for the trade across Canada, stewarded by the Canadian Council of Directors of Apprenticeship. A Red Seal endorsement on an Ontario Certificate of Qualification means the qualification is recognized in other provinces and territories without re examination, which matters for workers moving between provinces and for employers hiring from outside Ontario.

The Red Seal exam for this trade, written under the national title Instrumentation and Control Technician, has 125 multiple-choice questions, each with four possible answers and exactly one correct answer.

### How the 125 questions are distributed

| Major Work Activity | Questions |
| --- | --- |
| A. Performs common occupational skills | 12 |
| B. Installs and services process measuring and indicating devices | 30 |
| C. Installs and services safety and security systems and devices | 11 |
| D. Installs and services hydraulic, pneumatic and electrical systems | 14 |
| E. Installs, configures and services final control elements | 25 |
| F. Installs and services communication systems and devices | 12 |
| G. Installs and services control systems and process control | 21 |

By question type, this trade's exam runs 25 to 30% knowledge and recall, 40 to 45% procedural and application, and 25 to 30% critical thinking.

- [Red Seal exam breakdown for Instrumentation and Control Technician: question counts by task](https://red-seal.ca/eng/trades/instrumentcntltech/exam-information.shtml)
- [Red Seal exam preparation checklist](https://red-seal.ca/eng/resources/preparation-checklist.shtml)
- [How to register for a Red Seal exam](https://red-seal.ca/eng/resources/register.shtml)

## Already experienced? The Trade Equivalency Assessment

Workers with experience from outside Ontario's apprenticeship system, or from another country, can apply for a Trade Equivalency Assessment instead of starting an apprenticeship. Approval requires verifiable evidence of competency in the trade's Training Standard and experience at least equal to the trade's total training time; if approved, you challenge the certifying exam directly. The assessment costs $235 plus HST, and a reassessment with new evidence costs $100 plus HST, per [Skilled Trades Ontario's Trade Equivalency Assessment page](https://www.skilledtradesontario.ca/experienced-workers/trade-equivalency-assessment/).

## Certification is not the only paperwork

A Certificate of Qualification covers the person. Running a business in the trade carries its own obligations: many Ontario municipalities require a contractor licence on top of personal certification, and construction employers must complete WSIB registration before work begins. Both are indexed on our sister site: [municipal contractor licensing requirements by city](https://ontariotraderegistry.ca/licensing/) and [WSIB Form 1000, registration of constructors and employers](https://ontariotraderegistry.ca/compliance/wsib-form-1000/), on Ontario Trade Registry.

## What does an instrumentation and control technician earn in Ontario?

| Median wage | $44.00 per hour |
| --- | --- |
| Low | $35.00 |
| High | $56.00 |
| Occupation measured | Industrial instrument technicians and mechanics (NOC 22312) |
| Reference period | 2023-2024 |

Published by Employment and Social Development Canada through Job Bank, for Ontario as a whole. Read it as the pay range for the occupational group this trade belongs to, not a guaranteed rate: one NOC code can cover more than one trade, and wages vary by region, employer and experience.

## Is the 447A recognised outside Ontario?

This trade has been part of the Interprovincial Red Seal Program since 1964. 12 of Canada's 13 provinces and territories designate it Red Seal: AB, BC, MB, NB, NL, NS, NT, NU, ON, PE, SK, YT, Ontario among them. Its National Occupational Classification code is 22312, which is how federal labour market data refers to this occupation.

## Where can you train as an instrumentation and control technician in Ontario?

| Public training providers | 7 colleges deliver the in-school portion |
| --- | --- |
| Approved sponsors | 60 employers registered to train apprentices |
| Apprentices in training | 526 |

Counts are from Ontario's published apprenticeships dataset. A sponsor is the employer or union that registers and trains the apprentice; you need one before an apprenticeship can start.

## How dangerous is industrial work in Ontario?

Ontario does not publish injury figures per trade, only by sector. In 2024 the Ministry of Labour recorded 27 worker fatalities and 2,148 critical injuries under the industrial health and safety program. See [the ten-year counts and what they leave out](https://ontariocertificationregistry.ca/trades/safety/).

## Related Ontario trades

Other industrial sector trades with certification records on this registry:

- [Electric Motor System Technician (446A) certification requirements](https://ontariocertificationregistry.ca/trades/446a-electric-motor-system-technician/)
- [Entertainment Industry Power Technician (269E) certification requirements](https://ontariocertificationregistry.ca/trades/269e-entertainment-industry-power-technician/)
- [Facilities Technician (255B) certification requirements](https://ontariocertificationregistry.ca/trades/255b-facilities-technician/)
- [Optics Technician (Lens and Prism Maker) (225A) certification requirements](https://ontariocertificationregistry.ca/trades/225a-optics-technician-lens-and-prism-maker/)
- [Railway Car Technician (268R) certification requirements](https://ontariocertificationregistry.ca/trades/268r-railway-car-technician/)
- [Relay and Instrumentation Technician (288R) certification requirements](https://ontariocertificationregistry.ca/trades/288r-relay-and-instrumentation-technician/)
- [Thin Film Technician (225F) certification requirements](https://ontariocertificationregistry.ca/trades/225f-thin-film-technician/)
- [All 23 compulsory trades in Ontario](https://ontariocertificationregistry.ca/trades/compulsory/)

## Official verification sources

- Regulation[O. Reg. 876/21, Prescribed Trades and Related Matters (e-Laws)](https://www.ontario.ca/laws/regulation/210876)
- Certifying body[Skilled Trades Ontario: Instrumentation and Control Technician](https://www.skilledtradesontario.ca/trade-information/instrumentation-and-control-technician/)
- Act[Building Opportunities in the Skilled Trades Act, 2021 (e-Laws)](https://www.ontario.ca/laws/statute/21b28)
- Wages[Job Bank wage data, Employment and Social Development Canada](https://open.canada.ca/data/en/dataset/adad580f-76b0-4502-bd05-20c125de9116)
- Red Seal profile[red-seal.ca: Instrumentation and Control Technician trade profile](https://red-seal.ca/eng/trades/instrument-cntl-tech.shtml)
- Participation data[Ontario open data: Apprenticeships dataset](https://data.ontario.ca/dataset/apprenticeships)Classification, exam requirement and ratio status on this page are read directly from O. Reg. 876/21 as consolidated on e-Laws, not from secondary summaries. Facts not yet verified against a primary source are marked as not published rather than estimated.

---

Source: https://ontariocertificationregistry.ca/trades/447a-instrumentation-and-control-technician/